Trend Innovations

• We are offering Cut Section Model Of Shell and Tube condenser
• A tube-in-tube heat exchanger can achieve a net countercurrent flow, which allows temperature crossovers to be achieved so that the cold fluid can be heated above the hot fluid outlet's temperatures.

Additional Information:

• Delivery Time: 1 week
• Packaging Details: Cut Section Model Of Shell and Tube condenser

• Strain gauges convert the applied force, pressure, torque, ect., into an electrical signal which can be measured.
• The strain gauge is one of the most important sensor of the electrical measurement technique applied to the measurement of mechanical quantities. 

• Demonstartive Model
• The Parshall flume is an open channel flow metering device that was developed to measure the flow of surface waters and irrigation flows. The Parshall flume is a fixed hydraulic structure. It is used to measure volumetric flow rate in industrial discharges, municipal sewer lines, and influent/effluent flows in wastewater treatment plants. 

Additional Information:

• Item Code: TI100
• Production Capacity: 1 box
• Delivery Time: 1 week

The construction and principle of operation of Single Phase Energy Meters is explained below

There are four main parts of the operating mechanism

(i)      Driving   system

(ii)   Moving   system

(iii) Braking system

(iv) Registering system

Additional Information:

• Delivery Time: 1week
• Packaging Details: Wrapped

Additional Information:

• Delivery Time: 1 Week

Additional Information:

• Delivery Time: 1 -2 week

* To find quality of steam/ dryness fraction of steam

* To find efficiency of steam Boiler

* To evaluate thermal performance of steam surface condenser.

Þ It consist of Steam Boiler (Non– IBR), Separating and Throttling calorimeter, Steam Condenser (Shell and Tube type), Water Pump and other necessary instruments.

Þ All the instruments are calibrated for its accuracy and uncertainty.

Additional Information:

• Production Capacity: 0,001 kg/sec
• Delivery Time: 2 week

Additional Information:

• Production Capacity: 100/Month
• Delivery Time: 1 week
• Packaging Details: Wrapping with bubble sheet pack

The set-up consists of a Gasketed Plate Heat Exchanger with hot water and Cold water IN/OUT provision. Temperature tappings are provided

Additional Information:

• Production Capacity: 100/Month
• Delivery Time: 1 Week
• Packaging Details: Wooden

• To study the Vapour Compression air conditioning cycle.
• To Calculate Co-efficient of performance-(COP) by the use of P-H diagram.

• Digital Temp. Controller : 0-199.9°C,
• Digital Temp. Indicator: 0-199.9°C, with multi-channel switch
• Temperature Sensors: RTD PT-100 type.
• Standard make On/Off switch, Mains Indicator etc.

• 1 Self Contained "Split Air Conditioner Test Rig" Apparatus
• 1 Instruction Manual consisting of experimental procedures, block diagram etc.

Additional Information:

• Item Code: TI01
• Production Capacity: one per day
• Delivery Time: 2 week
• Packaging Details: wooden

• Crack Detection Microscope for the Concrete crack width mesuement.
• The Crack Detection Microscope is a precision apparatus, used for measuring cracks in concrete. It has its own adjustable light source for darkened conditions. The image is focused by turning a knurled knob on the side and the eye piece scale can be rotated through 360 degrees to align with the crack under examination.

Additional Information:

• Production Capacity: 1
• Delivery Time: 1 w

Þ In this test rig, we can cover performance parameters of the vortex tube & it tested for -

· Maximum Discharge

· COP Calculations

Þ It consist of Vortex Tube, Air Rotameter, FCV and other necessary instruments and other necessary instruments.

Þ All the instruments are calibrated for its accuracy and uncertainty.

Þ In this test rig, we can cover performance parameters of the steam nozzle & it tested for -

· Maximum Discharge

· Chocking Condition

· Efficiency Calculations

Þ It consist of Steam Boiler (Non IBR), Steam Condenser (Shell and Tube type), Water Pump and other necessary instruments and other necessary instruments.

Þ All the instruments are calibrated for its accuracy and uncertainty.

Þ Material and Process  Used: SS, MS, quality powder coated material, All mountings and accessories are calibrated and tested.

Additional Information:

• Delivery Time: 1 month

Additional Information:

• Production Capacity: 10
• Delivery Time: 2 Week
• Packaging Details: Wooden Box

• Model of all type of transducers 
• Inductive Transducer
• oxygen Transducer
• Ultrasonic Transducer
• Thermocouple
• Photo electric LDR

Additional Information:

• Delivery Time: 1 week

• "U" Tube Manometer for the measurement of the pressure and pressure differance.
• Digital manometers can be used to measure pressure anywhere. They don't rely on non-metric fluids, which means they do not require leveled surfaces to provide accurate readings. They can easily be linked to computers and programmable logic controllers (PLC). They are lightweight and portable.

Additional Information:

• Production Capacity: 10
• Delivery Time: 2 weeks